- Add comprehensive VL1 (ZeroTier protocol) fragmentation metrics:
* Track fragmented packets, fragments, reassembly failures
* Monitor fragment ordering issues and duplicates
* Histogram for fragments per packet distribution
- Add VL2 (TAP/Ethernet) fragmentation metrics for virtual ethernet interfaces:
* Track oversized frames from TAP devices
* Monitor frames that would fragment or drop
* Histogram for frame size distribution with common MTU buckets
- Integration across all TAP implementations (Linux, Mac, BSD, Windows)
This allows monitoring of fragmentation patterns for nodes participating
as members in ZeroTier networks, helping identify MTU mismatches and
optimize virtual ethernet performance.
This makes switching between physical networks
with full tunnel mode enabled more reliable.
There were issues with the physical default route or device
changing.
* Add test for primary port bindings to validator - See #2105
* Add delay to binding test
* Remove TCP binding logic from Binder to fix#2105
* add second control plane socket for ipv6
* fix controller network post endpoint
* exit if we can't bind at least one of IPV4 or IPV6 for control plane port
---------
Co-authored-by: Grant Limberg <grant.limberg@zerotier.com>
see commit fb6af1971 * Fix network DNS on macOS
adding that stuff to System Config causes this extra route to be added
which breaks ipv4 default route.
We figured out a weird System Coniguration setting
that works.
--- old
couldn't figure out how to fix it in SystemConfiguration
so here we are# Please enter the commit message for your changes. Lines starting
We also moved the dns setter to before the syncIps stuff
to help with a race condition. It didn't always work when
you re-joined a network with default route enabled.
See issue #2082
We use a call to libnatpmp::ininatpp to make sure the computer
has working network sockets before we go into the main
nat-pmp/upnp logic.
With basic exponenetial delay up to 30 seconds.
Stumbled upon this while debugging something else.
If we add search domain to our system configuration for
network DNS, then search domains work:
```
ping server1 ~
PING server1.my.domain (10.123.3.1): 56 data bytes
64 bytes from 10.123.3.1
```
It stopped working for ipv4 only networks in Monterey.
See #1696
We add some config like so to System Configuration
```
scutil
show State:/Network/Service/9bee8941b5xxxxxx/IPv4
<dictionary> {
Addresses : <array> {
0 : 10.2.1.36
}
InterfaceName : feth4823
Router : 10.2.1.36
ServerAddress : 127.0.0.1
}
```
The original way we applied default route, by forking
0.0.0.0/0 into 0/1 and 128/1 works, but if mac os has any networking
hiccups -if you change SSIDs or sleep/wake- macos erases the system default route.
And then all networking on the computer is broken.
to summarize the new way:
allowDefault=1
```
sudo route delete default 192.168.82.1
sudo route add default 10.2.0.2
sudo route add -ifscope en1 default 192.168.82.1
```
gives us this routing table
```
Destination Gateway RT_IFA Flags Refs Use Mtu Netif Expire rtt(ms) rttvar(ms)
default 10.2.0.2 10.2.0.18 UGScg 90 1 2800 feth4823
default 192.168.82.1 192.168.82.217 UGScIg
```
allowDefault=0
```
sudo route delete default
sudo route delete -ifscope en1 default
sudo route add default 192.168.82.1
```
Notice the I flag, for -ifscope, on the physical default route.
route change does not seem to work reliably.
* internal db metrics
* use shared mutexes for read/write locks
* remove this lock. only used for a metric
* more metrics
* remove exploratory metrics
place controller request benchmarks behind ifdef
* add new metrics for network config request queue size and sso expirations
* move sso expiration to its own thread in the controller
* fix potential undefined behavior when modifying a set
